Siemens SIMATIC IPC627E Скачать руководство пользователя

Страница: 35 / 164

SIMATIC IPC627E
Operating Instructions, 12/2018, A5E44297201-AA

Installing and connecting the device

3.1

Preparing for installation

3.1.1

Scope of delivery

Device and hardware for the device

●

Box PC SIMATIC IPC627E

●

2 mounting brackets

●

1 strain relief for USB and LAN interfaces

●

1 power plug latch

●

1 power supply cable (optional for AC power supply)

●

1 USB stick

Supplied data medium

On the supplied data medium (read-only), you can find:

●

Software and tools to restore your ordered Microsoft® Windows® operating system.

●

Device drivers for installation in operating systems

●

SIMATIC IPC627E Quick Install Guide

●

SIMATIC IPC627E operating instructions

●

Product information

●

Firmware/BIOS description

●

Operating instructions for your ordered Microsoft® Windows® operating system on this

device

Operating system

Depending on the ordered device configuration, the device is equipped with or without one of

the following installed operating systems.
You can find information on ordered Microsoft® Windows® operating systems under:

Important instructions and manuals for operating the device (Page 11) or Technical

specifications of the operating systems (Page 119).

Содержание SIMATIC IPC627E





































































































































































Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC627E, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды