Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 97 / 136

Device maintenance and repair

7.6 Installing the software

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

Select the partition on which you want to install the operating system.

Click "Next".
Installation is started. The Windows operating system is installed on the data medium.

Partitions in the delivery state for Windows 7

The following information applies to data storage media ≥ 100 GB.

Partition

Name

Size

File system

First

BOOT

100 MB

NTFS

Second

SYSTEM (C:)

160 GB

NTFS, start partition, swap partition

Third

DATA (D:)

Remainder

NTFS, primary partition

Information for systems with RAID or AHCI controller

Data carrier controllers unknown to the operating system must be made known to the

operating system prior to installation in the "Install Windows" installation program.

Requirement

You have copied the relevant controller driver to a USB stick.

Procedure

Connect the USB stick with the controller driver to the device.

Start the "Install Windows" installation program as described above.

Select "Load Drivers" in the Windows installation window.

Select the respective driver on the USB stick.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды