Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 86 / 136

Device maintenance and repair

7.5 Removing and installing hardware

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

NOTICE
Damage to the battery
Grease residues from your hands damage the battery.

•

Do not touch the battery with your hands.

•

Use suitable gloves, for example.

Note
The configuration data of the device may be deleted after battery replacement, depending on

the BIOS setting. With BIOS setting "Profile: User", the configuration data of the device is

retained; only the date and time must be set again.

1. Remove the battery from the socket

at the marked location.

2. Insert the new battery as shown.

3. Press the new battery centered into

the socket applying slight pressure.
Ensure that the battery is securely

seated.

4. Dispose of the old battery properly.

Further procedure

●

Connect all cables.

●

Close the device as specified in section "Open the device. (Page 52)".

●

Set the BIOS setup.
The configuration data of the device may be deleted after a battery replacement

depending on the BIOS setup setting.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды