Siemens SIMATIC IL43 Скачать руководство пользователя

Страница: 54 / 112

Expansions and configuration

10.4 Installing disk drives

SIMATIC Rack PC IL 43

10-8

Operating Instructions, Edition 09/2005, A5E00432875-01

Disk drive or removable disk rack installation

Steps for installing a disk drive in a horizontal drive carrier
1

Slide the disk drive into the carrier from

the front.

Remove any vertical drive carrier The

only way to get at the mounting screws

on the right side of the drive is through

the openings of the vertical carrier.

Mount the disk drive into the drive

carrier using four screws.

Insert the drive carrier module again.

Connect the power and data cables to

the disk drive.

10.4.3

Installing and removing a hard disk

Preparation

1. Unplug the device from mains and disconnect all cables.
2. Open the device.

Installing a disk drive

Steps for installing a disk drive
1

Connect the power and data cables

to the disk drive.

Hold the drive on the drive carrier

plate and secure it with 4 screws

(1).

Содержание SIMATIC IL43

















































































































Результаты поиска

Содержание SIMATIC IL43

Отзывы:

Похожие инструкции для SIMATIC IL43

Бренды по названию

Популярные бренды

Siemens SIMATIC IL43, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IL43

Отзывы:

Похожие инструкции для SIMATIC IL43

Бренды по названию

Популярные бренды