Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 95

Страница: 95 / 196

Parameterizing the Mobile Panel

5.7 General settings

TP1000F Mobile RO
Operating Instructions, 08/2017, A5E39831415-AA

Select the required data channel in the "Transfer channel" group.
–

PN/IE
Transfer is over PROFINET or Industrial Ethernet. This means an HMI device can

communicate over a switch or over a router in the local network.

–

Ethernet

To call up the addressing of the HMI device, press "Properties".
You can find the necessary information in "Specifying the IP address and name server

(Page 113)".

Confirm your entries.
The dialog closes.

The data channel for transfer is configured.

5.7.6

Storage management

5.7.6.1

Displaying memory distribution

This function displays the size of the flash memory and its archived data and program data

allocation.

Requirement

The Control Panel is open.

Procedure

Open the "System Properties" dialog using the "System" icon.

Change to the "Memory" tab.

①

Cache memory, available and used

②

RAM, available and used

NOTICE
Malfunction
If you change the allocation of the memory, malfunctions may occur.
Do not change the memory allocation in the "Memory" tab unless the message "Insufficient

memory" is displayed.

Содержание SIMATIC HMI TP1000F Mobile RO





































































































































































































Результаты поиска

Содержание SIMATIC HMI TP1000F Mobile RO

Отзывы:

Siemens SIMATIC HMI TP1000F Mobile RO, Руководство по эксплуатации, Страница: 95 / 196

Результаты поиска

Содержание SIMATIC HMI TP1000F Mobile RO

Отзывы: