manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Руководство по эксплуатации, Страница: 90 / 196

Поделиться
Скачать
Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 90

Parameterizing the Mobile Panel 

 

5.7 General settings 

 

TP1000F Mobile RO 

90

 

Operating Instructions, 08/2017, A5E39831415-AA  

The settings for the data and time of day have now been changed. The HMI device must be 

restarted after changes in the following cases: 

●

 

You have changed the time zone setting 

●

 

You have changed the "Daylight savings time currently in effect" check box setting 

See "Restarting the HMI device (Page 86)". 

5.7.3

 

Entering and deleting a password 

You can set and delete passwords with the following procedure: 

●

 

For security mode, as described in the section "Using the HMI device in password-

protected security mode (Page 75)". 

●

 

For security-related mode, as described in the section "Assigning a safety-related 

operating mode (Page 115)". 

Requirement  

●

 

A password that does not contain the following characters: 
–

 

Blank 

–

 

The special characters ' or " 

●

 

Password length ≤ 12 characters

 

 

 

NOTICE 
Keeping the password 
If the password is no longer available, you have no access to the Control Panel and the 

Windows CE taskbar. 
Backup password to protect it against loss. 

 

Содержание SIMATIC HMI TP1000F Mobile RO





































































































































































































Отзывы:

Нет отзывов