manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Руководство по эксплуатации, Страница: 72 / 196

Поделиться
Скачать
Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 72

Handling the Mobile Panel 

 

4.4 Testing Mobile Panel readiness for operation 

 

TP1000F Mobile RO 

72

 

Operating Instructions, 08/2017, A5E39831415-AA  

Testing the enabling button and emergency stop / stop button function 

 

 

Note 
Before testing the enabling button and emergency stop / stop button functions, read the 

information in the following sections: 

•

 

"Operating the enabling button (Page 67)" 

•

 

"Pressing the emergency stop / stop button (Page 68)". 

 

The HMI device must be connected to a connection box for the function test. 
1.

 

Press down the acknowledgment button until it engages. 
Check whether the plant switches to the safe operating state described in the plant 

documentation. 

2.

 

Press the emergency stop / stop button. 
Check whether the system switches to the safe operating state as specified in the plant 

documentation. 

Switching off 
1.

 

Pull out the connecting cable from the connection box. 
The display switches off. If you do not connect the connecting cable to a connection box 

within the next 5 minutes, the HMI device switches off. 

See also 

Connecting the KTP Mobile connecting cable to the connection box (Page 64) 
Fail-safe operation (Page 149) 

 

Содержание SIMATIC HMI TP1000F Mobile RO





































































































































































































Отзывы:

Нет отзывов