manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Руководство по эксплуатации, Страница: 151 / 196

Поделиться
Скачать
Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 151

 

TP1000F Mobile RO 
Operating Instructions, 08/2017, A5E39831415-AA  

151

 

 

Maintenance and care 

8 

8.1

 

Replacing the Mobile Panel 

When replacing an HMI device, the following applies: 

●

 

The TP1000F Mobile RO can only be replaced with a device of the same design. 

●

 

For a 1:1 data transfer from one HMI device to another, a replacement device with 

identical construction is required. 

Below you will find a description of how to replace an HMI device with a replacement device 

with identical construction. 

Replacement device with identical construction, manual backup exits  

1.

 

Insert the storage medium with the manually created backup into the slot of a 

replacement device with identical construction. 

2.

 

Proceed as described in the section "Functions for service and commissioning 

(Page 117)". 

See also 

Unplugging the connecting cable (Page 150) 

8.2

 

Servicing the Mobile Panel 

The HMI device is designed for low-maintenance operation. Also take into account the 

system components and accessories when carrying out maintenance. For maintenance, 

follow the safety instructions in "General safety instructions (Page 25)".  
The scope of maintenance includes the following function tests: 

●

 

Function test of enabling button 

●

 

Function test of emergency stop / stop button 

Depending on the Safety Integrity Level SIL of your application, the function tests are 

performed at the following intervals. 

●

 

SIL2: 1 x annually 

●

 

SIL3: 1 x monthly 

Содержание SIMATIC HMI TP1000F Mobile RO





































































































































































































Отзывы:

Нет отзывов