Siemens Simatic ET200pro Скачать руководство пользователя страница 524

Страница: 524 / 545

Appendix

A.6 Fail-safe shutdown of the ET 200pro Standard edition modules

ET 200pro distributed I/O system

524

Operating Instructions, 03/2013, A5E00335544-08

A.6

Fail-safe shutdown of the ET 200pro Standard edition modules

Introduction

The following structure describes how to implement a fail-safe shutdown of the ET 200pro

Standard modules.
Through the displayed structure (with the safety shutdown device: e.g. 3TK28), all outputs of

the connected ET 200pro Standard edition modules are switched into the safe OFF state.

Safety class SIL2/Category 3 is reached.

Principle of operation

The higher-level safety shutdown device, e.g. 3TK28, disconnects the supplies 2L+ and 2M

(24 V). The ET 200pro Standard edition modules operated on the voltage buses 2L+ and 2M

and their outputs are switched into the safe status. The supply via the 1L+ and 1M bus is not

used by these modules. The connections are not occupied.

Block diagram

Figure A-44 Higher-level safety circuit with safety shutdown device

Содержание Simatic ET200pro


































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Simatic ET200pro

Отзывы:

Похожие инструкции для Simatic ET200pro

Бренды по названию

Популярные бренды

Siemens Simatic ET200pro, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET200pro

Отзывы:

Похожие инструкции для Simatic ET200pro

Бренды по названию

Популярные бренды