Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 98

Страница: 98 / 126

Programming

5.7 Configuration function blocks

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0)
Manual, 06/2019, A5E46959434-AA

Table 5- 4

Sensor instance type-related parameters

Attributes BYTE Type 1 (push button) Type 2 (absolute input)

Type 3 (occupancy)

Type 4 (light sensor)

Read/Write

tShort

Deadtime

Hold time

Hysteresis

tDouble

Report time

Hysteresis min

tRepeat

Not used

Deadtime

Report time

tStuck

Not used

Deadtime

Read only

Resolution

tShortMin

Not used

5.7.16

DALI_SENSOR_SET_INST_PARAM

Description

DALI_SENSOR_INST_PARAM is used for setting the instance parameters of the input

device (sensor).

●

If the status of the sensor is configured (for example, sensor is added by using

DALI_SENSOR_ADD (Page 89)), the parameters are saved in the CM 1xDALI (refer to

data flow path 1 (Page 23)) and sent to the physical device (refer to data flow path 5

(Page 23)).

●

If the status of the sensor is not configured, the parameters are only sent to the physical

device (refer to data flow path 5 (Page 23)).

You can query the instance parameters of the sensor by using

DALI_SENSOR_QUERY_INST_PARAM (Page 95).

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы:

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 98 / 126

Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы: