Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 83

Страница: 83 / 126

Programming

5.7 Configuration function blocks

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0)

Manual, 06/2019, A5E46959434-AA

5.7.7

DALI_ECG_QUERY_GROUP

Description

DALI_ECG_QUERY_GROUP is used for querying the group membership of DALI control

gears.

●

When you set the input "PHY_DEV" to 1, this function block queries the group

membership from the physical device (refer to data flow path 6 (Page 23)).

●

When you set the input "PHY_DEV" to 0, this function block queries the parameters which

are saved in CM 1xDALI (refer to data flow path 2 (Page 23)).

You can set the group membership of control gear by using DALI_ECG_SET_GROUP

(Page 83).

Parameter

The following table shows the parameters of the function block:

Parameter Declaration Data type Memory

area

Description

QUERY

Input

BOOL

I, Q, M, D,

L or Con-

stant

Query the group membership of the control gear upon a rising edge.

ADDRES

USInt

I, Q, M, D,

L or Con-

stant

Specify the short address of the device.
Range: 0 to 63

PHY_DEV

BOOL

I, Q, M, D,

L or Con-

stant

Specify the location of parameters:

•

PHY_DEV = 0 : Query the parameters which are saved in CM

1xDALI.

•

PHY_DEV = 1 : Query the parameters from the physical device by

sending commands.

CM_DALI InOut

"DALI_CT

RL"

The data block of DALI_CTRL specifies the CM 1xDALI which com-

municates with the current function block.

BUSY

Output

BOOL

I, Q, M, D,

Status parameter:

•

BUSY = 0: Processing of job is terminated.

•

BUSY = 1: Job is still being committed.

ACTIVE

BOOL

I, Q, M, D,

Status parameter:

•

ACTIVE = 0: Job is not yet started.

•

ACTIVE = 1: Job is being executed.

DONE

BOOL

I, Q, M, D,

Status parameter:

•

DONE = 0: Job is not yet started or still executing.

•

DONE = 1: Job is executed without errors.

ERROR

BOOL

I, Q, M, D,

Status parameter:

•

ERROR = 0: No error occurs.

•

ERROR = 1: Error occurs during processing.

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы:

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 83 / 126

Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы: