manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 41 / 126

Поделиться
Скачать
Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 41

Programming 

 

5.5 Control gear dimming function blocks 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 

40

 

Manual, 06/2019, A5E46959434-AA 

5.5

 

Control gear dimming function blocks 

Control gear dimming function blocks are used for querying or setting the level and color of 

the control gears. 

5.5.1

 

DALI_ECG_SWITCH 

Description 

DALI_ECG_SWITCH is used for switching on or off control gear, and you can also define the 

on and off level with this switch. The on and off levels are neither saved in the CM 1xDALI 

nor in the DALI device (refer to data flow path 5 (Page 23)). 

Parameter 

The following table shows the parameters of the function block: 

 

Parameter  Declaration  Data type  Memory 

area 

Description 

ON 

Input 
 
 

BOOL 

I, Q, M, D, 

L or Con-

stant 

Switch on upon a rising edge. 

OFF 

BOOL 

I, Q, M, D, 

L or Con-

stant 

Switch off upon a rising edge. 

GROUP 

BOOL 

I, Q, M, D, 

L or Con-

stant 

Specify the short address or group address of the control gear: 

•

 

GROUP = 0: ADDRESS indicates the short address or broadcast. 

•

 

GROUP = 1: ADDRESS indicates the group address. 

ADDRES

S 

USint 

I, Q, M, D, 

L or Con-

stant 

Identify the address information of the CM 1xDALI. 
When GROUP = 0, ADDRESS 

indicates the short address or 

broadcast: 

•

 

0 to 63: Specify the short 

address of the device 

•

 

253: Broadcast the un-

addressed devices 

•

 

255: Broadcast all the devices 

When GROUP = 1, ADDRESS 

indicates the group address: 

•

 

0 to 15: Group address 

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Отзывы:

Нет отзывов