manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 26 / 126

Поделиться
Скачать
Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 26

 

Programming 

 

5.2 General information for programming 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

25

 

For the detailed parameter information on CM 1xDALI database and DALI device database, 

refer to the following table. 

Table 5- 1 

Description for database parameters 

Parameters 

Storage location 

Read-

only 

Description 

CM 

1xDALI 

DALI 

devices 

DALI device 

status 

✓

 

✓

 

✓

 

The basic status and extended status of control gears, and device status 

of sensors.  

Address status 

✓

 

 

✓

 

The address status of DALI device on the bus. CM 1xDALI cyclic queries 

all the address status of DALI devices on the bus through the back-

ground detection, and detects the following results:  

•

 

Whether each DALI device has a short address 

•

 

For control gear: the information of basic status, control gear type 

and extended status 

•

 

For sensor: the information of device status, number of instances and 

type of each instance 

Configuration 

parameters 

✓

 

✓

 

 

The basic parameters, extended parameters, group and scene parame-

ters of control gears and device parameters, instance parameters of 

sensors. The CM 1xDALI does not store the read-only parameters of the 

DALI devices.  

Operating hour 

of control gears 

✓

 

 

 

The CM 1xDALI stores the operating hour of configured control gears.  

5.2

 

General information for programming 

The following general information is useful for programming a DALI application: 

About function block (FB) 

●

 

All the FBs in CM 1xDALI library are asynchronous instructions. It is recommended to use 

the FBs in the same cyclic organization block (OB). 

●

 

Most of the FBs in the CM 1xDALI library are triggered by a rising edge, except for 

DALI_CTRL  (Page 26)and DALI_ECG_SWITCH_DIM (Page 42). 

●

 

If you call several FBs at the same time, they are queued. You can check the output 

parameters in each FB. 

About DALI_CTRL 

●

 

DALI_CTRL (Page 26) is the basic FB of CM 1xDALI. DALI_CTRL must be called in a 

cyclic OB, and be executed in every cycle. Do not use it in an interrupt OB. 

●

 

Each CM 1xDALI works with only one instance of DALI_CTRL FB. 

●

 

Specify the hardware ID of connected CM 1xDALI at the DALI_CTRL FB, and then 

connect the DALI_CTRL DB with the other FBs through the InOut parameter of CM_DALI. 

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Отзывы:

Нет отзывов