Siemens SIMATIC CN 4100 Скачать руководство пользователя страница 53

Страница: 53 / 76

8.1.2.3

Switching off the CPU module

Requirement

• You have adhered to the basics for mounting.

• The supply voltage is connected to the rack.

• The CPU module has been started.

Procedure

Press and hold the reset button for 6 seconds.

Result

The system powers down together with the CPU module.

8.1.3

Status LEDs of the CPU module

Definition

The status LEDs of the CPU module provide information about the operating mode of the CPU
or indicate errors.

Meaning for redundant CPU modules

The following table shows the status LEDs and their meaning.

RTC = Runtime Container

LED

Master module

Standby module

Continuous light

Flashes

Continuous light

Flashes

Power supply

Power supply OK

RUN

RTC running

STOP

RTC stopped

Master

RTC is master
Cycle / Engineering run‐
ning

LED is off

Standby

RTC has detected stand‐
by

Synchronization stand‐
by

RTC in standby mode

Synchronization stand‐
by

AH failure

Plant network discon‐
nected

Operation

8.1 Operating the CPU module

CN 4100 Communication System
Equipment Manual, 10/2021, A5E50871363-AA

Содержание SIMATIC CN 4100













































































Результаты поиска

Содержание SIMATIC CN 4100

Отзывы:

Siemens SIMATIC CN 4100, Руководство по эксплуатации оборудования, Страница: 53 / 76

Результаты поиска

Содержание SIMATIC CN 4100

Отзывы: