Siemens SIMATIC CN 4100 Скачать руководство пользователя страница 52

Страница: 52 / 76

8.1.2

Using the reset button

8.1.2.1

Switching on the CPU module

Requirement

• You have adhered to the basics for mounting.

• The supply voltage is connected to the rack.

• For power-on again: The CPU has been switched off before via the reset button.

Procedure for commissioning after connection

Switch on the supply voltage.

Procedure for power-on again

Press the reset button.

Result

The CPU module is switched on and the system starts.

8.1.2.2

Restarting the CPU module

Requirement

• You have adhered to the basics for mounting.

• The supply voltage is connected to the rack.

• The CPU module has been started.

Procedure

Press the reset button.

Result

The system restarts.

Operation
8.1 Operating the CPU module

CN 4100 Communication System

Equipment Manual, 10/2021, A5E50871363-AA

Содержание SIMATIC CN 4100













































































Результаты поиска

Содержание SIMATIC CN 4100

Отзывы:

Siemens SIMATIC CN 4100, Руководство по эксплуатации оборудования, Страница: 52 / 76

Результаты поиска

Содержание SIMATIC CN 4100

Отзывы: