Siemens SIMATIC CN 4100 Скачать руководство пользователя страница 33

Страница: 33 / 76

①

Rack

②

Contact washer

③

Fastening nut

④

Washer

⑤

Cable lug

⑥

Cable

⑦

Fixing bolt

⑧

Mounting level

Result

The rack is grounded via a cable.

5.6.4

Plugging in the module

Requirement

• The rack is mounted.

• The rack is grounded.

• The power supply is switched off.

• Required tools:

– TX20 screwdriver for tightening the fixing screws

Procedure

1. If necessary, remove the protective cover from the slot.

2. Insert the module into the slot.

Note

The edges of the slots are beveled to prevent incorrect installation of the modules.

Note

Pay attention to the slot assignment. CPU modules and communications modules have
special slots and must not be interchanged.

3. Tighten the fixing screws of the module with a torque of 1.2 Nm.

Result

The module has been plugged in.

Installation

5.6 Installation

CN 4100 Communication System
Equipment Manual, 10/2021, A5E50871363-AA

Содержание SIMATIC CN 4100













































































Результаты поиска

Содержание SIMATIC CN 4100

Отзывы:

Siemens SIMATIC CN 4100, Руководство по эксплуатации оборудования, Страница: 33 / 76

Результаты поиска

Содержание SIMATIC CN 4100

Отзывы: