Siemens SICAM Q80 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 240

Siemens SICAM Q80 Скачать руководство пользователя страница 24

24

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

5.1.1.1.1 Import / Export of device definitions

In order to be able to define parameter sets offline, the measurement device's structure (amount and type of
measurement channels) must be known. For each device configured, then, a device definitions file (*.umi) is saved to
the PC.

If you create a parameter set for a device on a PC with which the device had never previously been connected, it is
possible to adopt its device definitions from a different PC.

Export:

The definition files are saved in the specified folder.

Import:

All measurement devices in the selected folder which are not yet known to the system are made known to the

PC.

Note

The measurement device count is limited to 99.

5.1.1.1.2 Conclude measurement data

The smallest measurement interval is 30 min – shorted intervals are not generated. Repeated running of the
commend is acknowledged but no additional measurement intervals are generated.

The command can only be performed if no PC (except the one currently in use) is directly connected with the
device. If that is the case, there is a timeout error, since it is not possible to access the device for a specified
amount of time.

5.1.1.1.3 Active / Passive setting

Active

enables access to devices.

If multiple devices are selected, many actions are only applied to active devices. Set any devices which are
switched off or not accessible as passive so that the measurement status query of all devices can be carried out
quickly. Otherwise, performing the command for inaccessible devices will cause significant delays.

5.1.1.1.4 Actions with the mouse

Selection of a device

In the topology, the measurement location at which this device is active is highlighted:

If the device is not active at any measurement location, the passive locations are displayed.

Double-clicking on the device name

The last configuration edited is loaded

«
...
22
23
24
25
26
...
»

Содержание SICAM Q80

















































































































































































































































Отзывы:

Нет отзывов