Siemens SICAM Q80 Скачать руководство пользователя страница 143

Страница: 143 / 240

143

Operation modes and settings

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

Add device

Here, manually enter the devices whose data are to be automatically transfered. The definitions for devices which are
integrated via

UDP

is performed automatically.

Auto-Transfer Devices: Manually enter the devices whose data are to be automatically transfered

Properties:

Under

Properties

you set the

IP-address

and enter its

Name

and

Serial number

and activate the transfer

by means of

Status

Transfer Automatic:

The transfer can be set separately for each device. The beginning of the transfer is set using

Interval start

. For the

Interval

, the available settings range from 10 min to 1 week. Additionally, there is the option of

using a

user defined

interval. For devices which were integrated via UDP, the entry

UDP Autotransfer

is provided.

Data filter:

Older data can be ignored by means of

Data option - Data since...

Error sequence

: If the connection fails, it is possible to provide

Connection retries

at a specified

Interval

IP- Address:

With certain constellations, e.g. Modem, it is possible for the IP-address imported via UDP not to match

the measurement device's address. In this case, enter the IP-address manually and lock it by clicking ont he padlock
button.

146

Содержание SICAM Q80

















































































































































































































































Результаты поиска

Содержание SICAM Q80

Отзывы:

Siemens SICAM Q80, Системное руководство, Страница: 143 / 240

Результаты поиска

Содержание SICAM Q80

Отзывы: