Siemens SICAM Q80 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 240

Siemens SICAM Q80 Скачать руководство пользователя страница 138

138

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

Classification of events according to voltage range

Search with event count as criteria – displays a list of voltage channels with the channel count searched for.

5.1.6.4

Search results

In the task tree, the search results are listed:

*

Channel search_8 (3)

Eighth search in dialog "Channel search" with 3 results

context menu (right mouse button) allows deleting of result list

By making a channel permanent (in the example shown: U1_rms_pst_1), it's possible to protect it from being
deleted when making blanket deletions of whole channel groups.

* U1_rms_pst_1

Result channel named "U1_rms_pst" from the measurement with the ID 1

By clicking on the channel's entry, the data are displayed in the curve window

Context menu (right mouse button):

Display                   - Display of channel data in the curve window
Make permanent  - Blocks/enables deletion of channel
Delete                     - Deletes a channel (from list of results only)
Properties              - Display of result channel properties

Channel properties

Double-clicking on a channel or the context menu command

Display

switches to the curve window mode and the data

are displayed. The search screen is exited.

«
...
136
137
138
139
140
...
»

Содержание SICAM Q80

















































































































































































































































Отзывы:

Нет отзывов