Siemens SICAM Q100 7KG95 Series Скачать руководство пользователя страница 327 | Manualshive

Страница: 327 / 448

Siemens SICAM Q100 7KG95 Series Скачать руководство пользователя страница 327

9 Operation at Use of a PC

9.7 Example of a Parameterization and Measured Value Evaluation

327

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

9.7

Example of a Parameterization and Measured Value Evaluation

9.7.1

Task Definition

✧

Set the parameters via the Ethernet interface using the default IP address set upon delivery of the device.

✧

Configure SICAM Q100 according to the topology.

✧

Parameterize the indication of a limit violation for V

ab

> 11 kV with 10 % hysteresis and name the

indication.

✧

Parameterize a binary output that is switched on for the duration of the limit violation.

✧

Communicate via serial communication using device address 1, with a baud rate of 19.2 kbit/s, even
parity, full access rights, and a monitoring time of 1 min.

✧

Parameterize the Ethernet communication according to the network configuration specified by the system
operator.

✧

Assign any name and specify the time/date format as YYYY-MM-DD and the time in 24-hour format.

✧

Parameterize the Measurement recorder with an averaging time of 2 hours and activate the averaging
recorders for minimum and maximum values. Record all voltage harmonics.

✧

Allocate 50 % storage capacity to the Measurement recorder.

✧

Take over the factory-set report configuration.

✧

Activate the device configuration you have created as the active parameter set.

✧

Perform measurements, acquire the limiting value indication and record the measured values as defined
in the task.

9.7.2

Initial Situation

Topology

•

4-wire system

•

Rated input voltage (ph-ph): AC 10 kV

•

Rated input current: AC 100 A

•

Rated frequency: 50 Hz

•

Connection: any load via transformers

•

Voltage transformer: 10 000 V : 100 V

•

Current transformer: 100 A : 1 A

•

Primary nominal voltage: 230.00 V

•

Communication via Ethernet and RS485 interfaces

Network Configuration

•

Default IP address: 192.168.0.55

•

User IP address: 192.168.1.40 (customer-specific)

•

Subnet mask: 255.255.255.0

•

Default gateway: 192.168.1.1

MAN_SICAM_Q100_US.book Page 327 Wednesday, June 5, 2019 9:31 AM

«
...
325
326
327
328
329
...
»

Содержание SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Отзывы:

Нет отзывов