manualshive.com logo in svg

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 99 / 142

Поделиться
Скачать
Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 99

5

5.7 Input / Output Modules

99

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

5.7.6

Binary Inputs (optional)

The binary inputs (optional) can be used for static messages and impulse inputs.

Proceed as follows:

1. Activate/Deactivate one or both binary inputs by ticking the corresponding check box under 

1. 

 and/or 

2.

2. For each input used, set the 

Designation

 together with the 

Dimension

.

3. If you want to use the input as an external counter, you have to define the 

Factor

 e.g. as 

Energy increase per pulse (refer to chapter 5.7.2).

4. If you want to use the binary input to display binary information (0/1), 0 must be entered as 

a 

factor

.

5. Choose the binary input to be used for time 

Synchronization

 via minute impulses. The 

device will display the designation, not the number of the 

Binary input

.

 

6. Analog to measured values, binary inputs may be displayed on measurement screens (see 

chapter 5.6.2).  

Note

The designation of the binary input is displayed instead of the binary input number!

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов