manualshive.com logo in svg

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 92 / 142

Поделиться
Скачать
Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 92

5 

5.7 Input / Output Modules

92

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

5.7.1

Binary / Relay Outputs

The SICAM P has two binary outputs. The devices are optionally equipped with a module with 3 
additional relay outputs or a module with two binary outputs each.

In order to define the function of the two binary/relay outputs, select the binary output to be 
parameterized in field 

Binary outputs

 

→

 

No.

 In the 

Contents

 field, you can assign this binary 

output a function. You can select from the following options:

•

Off:

 binary output with no function

•

Device active

: The SICAM P active function allows you to monitor whether the device is 

switched on (contact closed). If there is no contact, the device is switched off or broken.

•

Limit values

: Here, you can output the limit value group signals via the binary outputs. The 

pulse length indicates how long the binary contact is closed by means of a signal from a limit 
value group.

•

Energy counter

: If you assign this function to a binary output, the consumption or supply of 

the selected work is output as a pulse. Select a measured value and the related measure-
ment point. Set a limit value (energy increase per pulse) for which a pulse should be trig-
gered. The parameterizable range (minimum and maximum value) can be found by entering 
the max. consumer power in the field 

Help

. 

 

The pulse duration can be selected in increments 

of 50 ms between 50 ms and 500 ms in the  

Pulse

 field .

You will find a description of the energy pulse measurement in chapter 5.7.2.

•

Direction of rotation

: output the rotation direction of the voltage

•

1: Contact activated: Direction of rotation for clockwise display (phase sequence A-B-C, 

clockwise rotation)

•

0: Contact deactivated: Direction of rotation for anti-clockwise display (2 phases inter-

changed, anti-clockwise rotation)

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов