Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 84

Страница: 84 / 142

5.3 Date / Time Settings and Transmit

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

5.3

Date / Time Settings and Transmit

You can set the date and time of the internal clock of the SICAM P using the SICAM P Parame-
terization PC software. You can either accept the current PC time or define and transmit a freely
selectable system time. To do this, proceed as follows:

To set the internal clock and transmit the time to a connected device, you have two options for
calling up the

Send date and time

dialog window:

Select the menu item

Device

→

Setup device clock

, or

click the clock symbol in the toolbar.

The

Send date and time

dialog window is displayed.

Send PC time

1. Click the

Send PC time

button to send the current PC time.

2. If the PC time has been transmitted correctly and accepted by the connected device, a con-

firmation will be displayed.

3. Click the

Close

button.

Send manual time setting

1. Change the entries in the fields

Day

Min

using your keyboard.

2. Then click

Send time manually

3. If the PC time has been transmitted correctly and accepted by the connected device, a con-

firmation will be displayed.

4. Click the

Close

button.

Содержание SICAM P 7KG7750















































































































































Результаты поиска

Содержание SICAM P 7KG7750

Отзывы:

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 84 / 142

Результаты поиска

Содержание SICAM P 7KG7750

Отзывы: