Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 82

Страница: 82 / 142

5.1 Basics

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

5.1

Basics

In order to program your SICAM P via the PC software SICAM P Parameterization you have to
prepare for operation or parameterization:

Preconditions

•

The device is ready to operate.

•

The PC software SICAM P Parameterization (ordering number see chapter 1.3) is installed
on your PC.

•

The parameterization cable set (ordering number see chapter 1.3) or a RS485 converter is
available.

Parameterization

1. Connect the device and the PC as described in the online help.

2. Set the connection parameters on the device:

•

Select the protocol "PC-RS485".

•

Select the baud rate for the connection.

3. Set the connection parameters in the PC software SICAM P Parameterization (

Connection

→

Setup connection

). Make sure to use the same baud rate.

4. Load the settings from the device (

Device

→

Connection configuration

→

Receive

5. Edit the settings in the PC software.

6. Send the new settings to the device again (

Device

→

Connection configuration

→

Send

Note

SICAM P Parameterization displays the parameters depending on the ordering number of the
device.

Reading the ID from the device recognizes the device type and sets the functional scope.

Note

All others functions of SICAM P Parameterization are described in the online help (key F1).

Содержание SICAM P 7KG7750















































































































































Результаты поиска

Содержание SICAM P 7KG7750

Отзывы:

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 82 / 142

Результаты поиска

Содержание SICAM P 7KG7750

Отзывы: