Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 104

Страница: 104 / 142

5.8 Additionals

104

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

5.8.3

Limit Value Groups

In SICAM P, you can parameterize up to 7 limit value groups. For limit value group 7, only volt-
ages are allowed.

Every

limit value group

provides the option to monitor whether the

measurements

exceed (

)

or fall short of (

) a measured value that is entered. In each of the seven limit value groups, up

to six measured quantities (no power quantities) can be

ANDed

ORed

The limit value groups set can be allocated either to binary outputs or to the internal counters.
The oscilloscope can be triggered using a limit value group 1 to 6.

•

Filter time: Time for which a threshold breach must remain in order to trigger an alarm. Input
from 0.0 s to 9.9 s.

•

Hysteresis: Entry from 0.1 % to max. 10 %. The value relates to the nominal values for the
individual measured values.

Note

To make sure that limit violations will be registered, enter a filter time

≥

1 s.

Note

If the device provides additional analog inputs (optional), you can use external measurement sig-
nals for limit-value monitoring.

Note

Limit value group 7 allows you to monitor the measured voltages in real time and logs the mea-
sured value that caused a limit violation.

Содержание SICAM P 7KG7750















































































































































Результаты поиска

Содержание SICAM P 7KG7750

Отзывы:

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 104 / 142

Результаты поиска

Содержание SICAM P 7KG7750

Отзывы: