Siemens SICAM 7KG85X Скачать руководство пользователя страница 78

Страница: 78 / 281

Serial Server

Table 2-24

Description of the Parameters in the Serial Server

Parameter

Description

Good messages

Total number of messages received that were detected as valid Modbus messages

CRC errors

Total number of messages received in which CRC errors were detected

Exception responses

Counters of the transmitted exception response messages

Broadcast messages

Total number of the broadcast messages received with the server address 0

Access rights violations

Total number of write accesses received if the parameter Access rights is set to
Read only in the Communication serial window.

Bus Protocol IEC 60870-5-103

Function Description

The serial communication using the IEC 60870-5-103 protocol is executed via the RS485 interface.

Configuration via Web Pages

Configuration of the Serial Communication with IEC 60870-5-103 via RS485 Interface

To change the IEC 60870-5-103 settings in the Configuration tab, proceed as follows:

•

In the navigation window, click Communication serial and select IEC 60870-5-103 as the Bus protocol.

•

Configure the respective parameters according to the following table.

Settings for Communication Serial, IEC 60870-5-103

Parameter

Default Setting

Setting Range

Bus protocol

Modbus RTU

None
Modbus RTU
IEC 60870-5-103

Device address

1 to 254

Baud rate

9600 bit/s

9600 bit/s
19 200 bit/s
38 400 bit/s

Measured value range

120 %
equivalent to a measured value
range from -4096 to +4095 (-120
% to +120 %)

120 %
240 %
equivalent to a measured value
range from -4096 to +4095 (-120
% to +120 % or -240 % to +240 %)

Transmit energy

Yes (every minute)
No

Transmission of the 1st to 40th
harmonics HV and HI

No
Yes

Cyclic sending period

50 * 100 ms

30 * 100 ms to 600 * 100 ms

Communication supervision time

600 * 100 ms

0 s = none
100 ms to 6 553 400 ms

NOTE

For the serial communication with IEC 60870-5-103, the parity is permanently set to even.

2.7.2

2.7.2.1

2.7.2.2

Basic Functions

2.7 Serial Communication

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Содержание SICAM 7KG85X


























































































































































































































































































Результаты поиска

Содержание SICAM 7KG85X

Отзывы:

Siemens SICAM 7KG85X, Руководство пользователя, Страница: 78 / 281

Результаты поиска

Содержание SICAM 7KG85X

Отзывы: