Siemens SICAM 7KG85X Скачать руководство пользователя страница 67

Страница: 67 / 281

[sc_communication_modbus_TCP, 1, en_US]

Figure 2-28

Configuration Tab, Modbus TCP Settings

•

Configure the respective parameters according to the following table.

Table 2-19

Settings for Modbus TCP

Parameter

Default Setting

Setting Range

Standard port number

502

502
Not settable

Access rights

Full

Full
Read only

User-defined port 1

No
Yes

Port number

503

503 to 65 535

Access rights

Read only

Full
Read only

Port number

504

503 to 65 535

Access rights

Read only

Full
Read only

This parameter is available only if User-defined port 1 is set to yes.

Basic Functions
2.6 Ethernet Communication

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Содержание SICAM 7KG85X


























































































































































































































































































Результаты поиска

Содержание SICAM 7KG85X

Отзывы:

Siemens SICAM 7KG85X, Руководство пользователя, Страница: 67 / 281

Результаты поиска

Содержание SICAM 7KG85X

Отзывы: