Siemens SICAM 7KG85X Скачать руководство пользователя страница 47

Страница: 47 / 281

AC Measurement

Configuration via Web Pages

Configuration of the AC Measurement

To change the AC measurement settings in the Configuration tab, proceed as follows:

•

In the navigation window, click AC measurement.

[sc_config_ac_measurement_p85x, 1, en_US]

Figure 2-13

Configuration Tab, AC Measurement

•

Configure the respective parameters according to the following table.

Table 2-9

Settings for AC Measurement

Parameter

Default Setting

Setting Range

AC measurement
Rated frequency

50 Hz

50 Hz
60 Hz

2.5

2.5.1

Basic Functions
2.5 AC Measurement

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Содержание SICAM 7KG85X


























































































































































































































































































Результаты поиска

Содержание SICAM 7KG85X

Отзывы:

Siemens SICAM 7KG85X, Руководство пользователя, Страница: 47 / 281

Результаты поиска

Содержание SICAM 7KG85X

Отзывы: