manualshive.com logo in svg

Siemens SICAM 7KG85X, Руководство пользователя, Страница: 135 / 281

Поделиться
Скачать
Siemens SICAM 7KG85X Скачать руководство пользователя страница 135

Waveform Records

Function Description

When a trigger function is activated, a waveform recorder records the following values:

•

Voltages

•

Currents

The following table shows all trigger sources of the waveform recorder, as well as the corresponding measure-
ment time base and trigger conditions.

Table 6-14

Triggers of the Waveform Recorder

Trigger Source

Measurement Time
Base

Trigger Conditions

Voltage trigger

1/2 cycle

The trigger starts if one of the following conditions is
met:

•

The measured value > the upper threshold

•

The measured value < the lower threshold

•

A voltage event occurs.

Current trigger

1/2 cycle

The trigger starts if one of the following conditions is
met:

•

The measured value > the upper threshold

•

The measured value < the lower threshold

You can parameterize the trigger sources and switch them on/off separately. If the trigger is switched off,
recording cannot be initiated.
Finishing of the waveform recording depends on the configured recording duration. The waveform record is
written to the SD card for subsequent evaluation.
The nominal sampling rate for the waveform recorder is 10 240 samples per second, that is 204 samples per
cycle for the 50-Hz system.

6.5

6.5.1

Power Quality
6.5 Waveform Records

134

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Содержание SICAM 7KG85X


























































































































































































































































































Отзывы:

Нет отзывов