Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 95

Страница: 95 / 130

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02

Appendix

A.1

Modbus TCP

Detailed information about Modbus can be found at the Modbus Website

(

http://www.modbus.org

)

A.1.1

Function codes

Function codes control the data exchange. In doing so, a function code tells the slave which

action it is to take.
If an error occurs, the most significant bit (MSB) is set in the FC byte of the response frame.

Supported Modbus function codes

Table A- 1

Supported Modbus function codes

Function in accordance with Modbus specification

0x01

Read Coils

0x02

Read Discrete Inputs

0x03

Read Holding Registers

0x04

Read Input Registers

0x05

Write Single Coil

0x06

Write Single Register

0x0F

Write Multiple Coils

0x10

Write Multiple Registers

0x2B

Read Device Identification

0x14

Read File Record (for average values)

0x64

Siemens specific Function Code

Содержание SENTRON PAC2200CLP



































































































































Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы:

Siemens SENTRON PAC2200CLP, Руководство по эксплуатации продукта, Страница: 95 / 130

Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы: