Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 83

Страница: 83 / 130

Technical specifications

8.1 Technical specifications

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02

Connection elements

The specified conductor cross-sections describe the capacity of the connection terminals.

When selecting the conduction cross-sections, always pay attention to the possible current

load and ensure adequate cable protection.

Current, power supply

5 A device

65 A device

Conductor cross-section for copper cable (Cu)

Rigid

0.2 ... 6.0 mm

[AWG 24...10]

0.75 ... 35 mm²

[AWG 19 ... 2]

Flexible

0.2 ... 4.0 mm²

[AWG 24...12]

1 ... 35mm²

[AWG 18 ... 2]

Flexible with end sleeve, without plastic

sleeve

0.2 ... 4.0 mm²

[AWG 24...12]

0.75 ... 25 mm²

[AWG 19 ... 4]

Flexible with end sleeve and plastic sleeve

0.25 ... 4.0 mm²

[AWG 24...12]

0.75 ... 25 mm²

[AWG 19 ... 4]

2-wire, same cross-section

Rigid

0.2 ... 1.5 mm²

[AWG 24 ... 16]

0.75 ... 10 mm²

[AWG 19 ... 8]

Flexible

0.2 ... 1.5 mm²

[AWG 24 ... 16]

1 ... 4mm²

[AWG 18 ... 12]

Flexible with end sleeve, without plastic

sleeve

0.25 ... 0.75 mm²

[AWG 24 ... 19]

0.75 ... 4 mm²

[AWG 19 ... 12]

Flexible with TWIN end sleeve and plastic

sleeve

0.5 ... 2.5 mm²

[AWG 20 ... 14]

0.75 ... 4 mm²

[AWG 19 ... 12]

Tightening torque

0.5 ... 0.6 Nm

[4.4 ... 5.3 lb-in]

3 Nm

[26.6 lb-in]

Conductor cross-section for copper cable (Cu) for

UL market

AWG 10 ... 4

Solid or stranded with ferrules

Conductor cross-section for copper cable (Cu) for

CSA market

AWG 8 ... 4

Compact stranded

Содержание SENTRON PAC2200CLP



































































































































Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы:

Siemens SENTRON PAC2200CLP, Руководство по эксплуатации продукта, Страница: 83 / 130

Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы: