Siemens SENTRON PAC2200CLP Скачать руководство пользователя страница 41

Страница: 41 / 130

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02

Connection

4.1

Safety notes

Notes

DANGER

Hazardous voltage
Will cause death, serious personal injury, or equipment damage.

Turn off and lock out all power supplying this equipment before working on this device.

DANGER

Open transformer circuits will result in electric shock and arc flash hazards
Will cause death, serious personal injury, or equipment damage.

For the 5 A device it is only possible to measure the current via external current

transformers. The current transformer circuit is not protected by a fuse. Do not open the

secondary circuit of the current transformers under load. Short circuit the secondary current

terminals of the current transformer before removing this device. The safety information for

the current transformers used must be followed.

WARNING

Hazardous voltage

May cause death, serious personal injury, or equipment damage.

•

Always open or disconnect circuit from power-distribution system (or server) of building

before installing or servicing current transformers.

•

The current transformers may not be installed in equipment where they exceed 75

percent of the wiring space of any cross-sectional area within the equipment.

•

Restrict installation of current transformers in an area where it would block ventilation

openings.

•

Restrict installation of current transformers in an area of breaker arc venting.

•

Not suitable for Class 2 wiring methods and not intended for connection to Class 2

equipment.

•

Secure current transformers and route conductors so that they do not directly contact

live terminals or bus.

Содержание SENTRON PAC2200CLP



































































































































Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы:

Siemens SENTRON PAC2200CLP, Руководство по эксплуатации продукта, Страница: 41 / 130

Результаты поиска

Содержание SENTRON PAC2200CLP

Отзывы: