Siemens SENTRON PAC2200 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 130

Siemens SENTRON PAC2200 Скачать руководство пользователя страница 50

Connection

4.4 Connecting the communication cable

PAC2200

48

Equipment Manual, 12/2019, L1V30415167B-03

Connection example for the 65 A device

(1) Three-phase measurement, four conductors, direct connection to the low-voltage network

Figure 4-5

Direct connection to the low-voltage network.

4.4

Connecting the communication cable

Depending on the device version, the following communication interfaces are available:

● Ethernet

● RS485

● M

-BUS

4.4.1

Ethernet communication cable

This interface is available as an option.
Always use a shielded cable for the Ethernet data cable.
1. Plug the RJ45 cable connector into the RJ45 device socket until the connector engages in

the socket.
2. Provide sufficient mechanical strain relief for the Ethernet cable.
3. Ground the shield of the cable (see chapter Grounding of the Ethernet/RS485 cable

(Page 50)).

«
...
48
49
50
51
52
...
»

Содержание SENTRON PAC2200



































































































































Отзывы:

Нет отзывов