Siemens SENTRON PAC2200 Скачать руководство пользователя страница 29

Страница: 29 / 130

Description

2.5 Communication

PAC2200
Equipment Manual, 12/2019, L1V30415167B-03

2.5.1

Ethernet

Permits communication via the following protocols:

●

Modbus TCP

The device can be configured via Modbus TCP

●

Web server (HTTP)

Protocol can be used to read out the measured values via web browser.

●

SNTP

The SNTP (Simple Network Time Protocol) is used to automatically synchronize the internal

clock with a time server within the network.
Three function modes are available:

●

No synchronization.

●

Date/time synchronization via device request
The IP address of an NTP server must be configured. With this, the PAC2200

automatically requests the current time from the server and resets its internal clock, if

necessary.

●

Date/time synchronization via SNTP server broadcast
The PAC2200 receives broadcast time frames, which are sent from an NTP server. This

is practical, if the internal clocks in several devices in the same network
should be synchronous.

If the IP address of the NTP server has been configured, the PAC2200 only responds to

these telegrams. Furthermore, it can send a request to the server, if necessary.

●

DHCP

Stands for "Dynamic Host Configuration Protocol". Protocol for obtaining network settings

from a DHCP server. Network settings are assigned automatically.

2.5.2

RS485

Enables communication via MODBUS RTU protocol. This interface features simple topology

and high immunity against EMC interference.
The data is transmitted differentially via two wires A and B. The third wire "COM" serves as

the common ground potential.
Grounding of the cable shield:
The serial Modbus data cable should be shielded. The shield should be connected to

protective ground at one end of the cable at least.
Grounding of the COM line:

Содержание SENTRON PAC2200



































































































































Результаты поиска

Содержание SENTRON PAC2200

Отзывы:

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 29 / 130

Результаты поиска

Содержание SENTRON PAC2200

Отзывы: