Siemens SENTRON PAC2200 Скачать руководство пользователя страница 25

Страница: 25 / 130

Description

2.3 Averaging measured values

PAC2200
Equipment Manual, 12/2019, L1V30415167B-03

Secondary values: Non-resettable energy counters. Transformer ratio is not taken into

account in the calculation.
MID: MID registers are marked in the menu with MID mark. Marked registers are suitable for

billing purposes.

Indicates the year the MID marking was affixed

2.3.3

History of active energy consumption

Based on selected recordings of energy consumption over time, users can perform a

targeted analysis of their energy consumption for the purpose of optimizing their energy

usage. The power monitoring devices have a daily energy counter and a monthly energy

counter.

●

The daily energy counter records the active energy for each day of the preceding two

months.

●

The monthly energy counter records the active energy for each month of the preceding

two years.

This function is available only in conjunction with communication interfaces. A list of

available measured values can be found in chapter Active energy history with Modbus

function code 0x14 (Page 117).

Содержание SENTRON PAC2200



































































































































Результаты поиска

Содержание SENTRON PAC2200

Отзывы:

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 25 / 130

Результаты поиска

Содержание SENTRON PAC2200

Отзывы: