Siemens SENTRON PAC2200 Скачать руководство пользователя страница 17

Страница: 17 / 130

Description

2.1 Performance features

PAC2200
Equipment Manual, 12/2019, L1V30415167B-03

Security

●

Hardware write protection

●

Password protection

●

Access protection IP filter

●

Modbus TCP port, configurable

●

HTTP port, configurable

●

Dynamic host configuration protocol (DHCP) included

●

Simple Network Time protocol (SNTP) included

●

Attachment of lead seals possible

Using "Password protection" and "Hardware write protection", you can protect against write

access to the device settings of the PAC2200.
The protection intervenes in case of the following actions:

●

Modify parameters in device

●

Reset maximum

●

Reset minimum

●

Reset counter

●

Reset device

●

Reset device to factory settings

●

Reset password

●

Update firmware on device

The data can be read without any restrictions.

Note
Activate hardware write protection
When connecting the measuring device to a network, it is recommended that the hardware

write protection is activated.

Tariffs

PAC2200 supports 2 tariffs for the integrated energy counter (high and

low tariff).
Control of tariff switching
Tariff switching can be controlled via the digital input or the

communication interfaces.

Time-related switching is only possible using a higher-level system.

Содержание SENTRON PAC2200



































































































































Результаты поиска

Содержание SENTRON PAC2200

Отзывы:

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 17 / 130

Результаты поиска

Содержание SENTRON PAC2200

Отзывы: