manualshive.com logo in svg

Siemens SENTRON PAC2200, Руководство по эксплуатации продукта, Страница: 118 / 130

Поделиться
Скачать
Siemens SENTRON PAC2200 Скачать руководство пользователя страница 118

Appendix 

 

A.1 Modbus TCP 

 

PAC2200 

116

 

Equipment Manual, 12/2019, L1V30415167B-03 

A.1.11

 

Modbus command parameters 

Addressing the command parameters 

You can apply the Modbus function code 0x06 to the command parameters.  

Table A- 13  Command parameters 

Offset  

Number 

of r 

egisters  

Name 

Unit 

Format 

Value range 

Access 

60004 

1 

Reset energy counter 

- 

unsigned 

short 

0 = 

all 

W 

1 = 

Active energy import tariff 1 

2 =  

Active energy import tariff 2 

3 = 

Active energy export tariff 1 

4 = 

Active energy export tariff 2 

5 = 

Reactive energy import 

tariff 1 

6 = 

Reactive energy import 

tariff 2 

7 =  

Reactive energy export 

tariff 1 

8 = 

Reactive energy export 

tariff 2 

9 = 

Apparent energy tariff 1 

10 = 

Apparent energy tariff 2 

60005 

1 

Synchronization of the 

demand period 

Min. 

unsigned 

short 

1 ... 60 

W 

60006 

1 

Switching tariff 

- 

unsigned 

short 

0 = 

Main tariff 

W 

1 = 

Secondary tariff 

60007 

1 

Acknowledge the diagnos-

tics bits

3)

 (cf. stored bits in 

unsigned long beginning 

offset 205) 

- 

unsigned 

short 

0 ... ffffh 

W 

60008 

1 

Switching outputs (if pa-

rameterized) 

- 

unsigned 

short 

0ffh ... 1ffh 

W 

Byte 0  

= 0 

Digital output 0.0 

Byte 1  

= 0 

OFF 

Byte 1  

= 1 

ON 

60009 

1 

Switching command for 

vector group 

- 

unsigned 

short 

High 0 ... 99, Low 0 ... 1 

High byte group assignment 

Low byte 1 = ON, 0 = OFF  

W 

65300 

1 

Activation of IP / Ethernet 

configuration 

- 

unsigned 

short 

0 

W 

3) The Modbus Master must acknowledge these diagnostics bits. 

Содержание SENTRON PAC2200



































































































































Отзывы:

Нет отзывов