Siemens SENTRON ATC6300 Скачать руководство пользователя страница 93

Страница: 93 / 210

Connection

7.3 Connection of Siemens SENTRON switching devices

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

Note
According to IEC regulations, the fusible element must be connected via a cable compliant

with IEC 61439-1 which is protected against ground faults and short circuits. To this end,

please observe the applicable national standards for electrical installations.

Note
The connection diagram shows a typical connection of the ATC with 3VA The connection

diagram is valid for 230 V AC. All SEO drives can be used. For this purpose the relevant

technical specifications of the drive, the circuit breaker and the ATC6300 have to be

observed. You can find more information on the technical specifications in the corresponding

manuals.

General setting

Table: Output function

Table: Input function

Param-

eter

Setting Con-

nection

Param-

eter

Setting

Con-

nection

Param-

eter

Setting

P05.07 Chg.

Pul.

P11.04.

Open Line 1 circuit

breaker

P10.01.

Line 1 breaker closed (feedback 1)

P11.05.

Close Line 1 circuit

breaker

P10.02.

Line 2 breaker closed (feedback 2)

P11.06.

Open Line 2 circuit

breaker

P10.03.

Line 1 circuit breaker protection (Trip

P11.07.

Close Line 2 circuit

breaker

P10.04.

Line 2 circuit breaker protection (Trip

If the 3VA molded case circuit breaker is used in combination with an SEO, the following

minimum parameters must be observed:

P05.06 Delay,

feedback signal

P06.07 Delay,

voltage present

P06.08 Delay,

Line 2 OK

P07.07 Delay,

voltage present

P07.08 Delay,

Line 1 OK

3VA22

2 s

Содержание SENTRON ATC6300



















































































































































































































Результаты поиска

Содержание SENTRON ATC6300

Отзывы:

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 93 / 210

Результаты поиска

Содержание SENTRON ATC6300

Отзывы: