Siemens SENTRON ATC6300 Скачать руководство пользователя страница 57

Страница: 57 / 210

Functions

5.1 Basic functions

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

5.1.9.2

Table of commands

The following table lists the available commands:

Code Command

Access level required Description

C01

Reset maintenance 1

Advanced

Reset maintenance interval hours 1

C02

Reset maintenance 2

Advanced

Reset maintenance interval hours 2

C03

Reset maintenance operations 1

Advanced

Reset maintenance interval for operating cycles 1

C04

Reset maintenance operations 2

Advanced

Reset maintenance interval for operating cycles 2

C05

Reset general counters CNTx

User

Sets the generic counter CNTx to zero

C06

Reset LIMx limits

User

Resets the status of the retained LIMx limits

C07

Reset hours counter Line 1 / Line 2 Advanced

Resets the hours counter for the presence / ab-

sence of Line 1 and Line 2 within the respective

limits

C08

Reset hour counters Breaker 1 /

Breaker 2

Advanced

Resets the hour counters for the closing / opening

processes of breakers 1 and 2

C09

Reset breaker operation

Advanced

Resets the counting of operating cycles for break-

ers 1 and 2

C10

Reset event log

Advanced

Deletes the list of historical events

C11

Reset default parameters

Advanced

Resets all the parameters in the setup menu to

the default values

C12

Save parameters in backup memory Advanced

Stores a copy of the currently set parameters in a

backup memory, so that they can be restored at a

later date

C13

Reload parameters from backup

memory

Advanced

Transfers the parameters stored in the backup

memory to the memory of the active settings

C14

Forced I/O

Advanced

Enables test mode so you can manually energize

any output.

Note: In this mode, the installation technician has

sole responsibility for the control of the outputs

C15

Reset A03 - A04 alarms

Advanced

Restores the opening or closing command of the

switching devices after generating the alarms A03

- A04

C16

Simulates line failure

Advanced

The device switches to the AUT mode and for two

minutes simulates the failure of the priority line.

After this, it performs a load switchover as pro-

grammed.

Содержание SENTRON ATC6300



















































































































































































































Результаты поиска

Содержание SENTRON ATC6300

Отзывы:

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 57 / 210

Результаты поиска

Содержание SENTRON ATC6300

Отзывы: