manualshive.com logo in svg

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 49 / 210

Поделиться
Скачать
Siemens SENTRON ATC6300 Скачать руководство пользователя страница 49

 

Functions 

 

5.1 Basic functions 

3KC ATC6300 transfer control device 
Manual, 03/2018, L1V30535632002A-01 

47

 

5.1.6.1

 

Properties of the alarms 

Various properties can be assigned to each alarm, including the user alarms (UAx see 

chapter User alarms (Page 50)). 

●

 

Alarms enabled (active)  

General enabling of the alarm.  

If an alarm has not been enabled, the procedure is as if the alarm did not exist. 

●

 

Only AUT (Aut)  

The alarm can only be triggered if the ATC6300 is in automatic mode. 

●

 

Retention alarm (Retent)  

Remains stored, even after the triggering cause has been removed. 

●

 

Global alarm (Glb Al)  

Activates the output which is assigned to this global alarm function (see chapter Table of 

functions of the digital outputs (Page 112)) 

●

 

Lock BRK1 (Lock 1)  

On occurrence of the alarm, no further commands are sent to switching device 1. 

●

 

Lock BRK2 (Lock 2) 

On occurrence of the alarm, no further commands are sent to switching device 2. 

●

 

Siren (Siren)  

Activates the output assigned to this function, as configured in the Table of alarms 

(Page 49) 

●

 

Inhibit (Inhib.)  

The alarm can be temporarily deactivated by activating a programmable input with the 

alarm inhibit function. 

●

 

No LCD (No LCD) 

The alarm is managed normally, but not shown on the display. 

 

Содержание SENTRON ATC6300



















































































































































































































Отзывы:

Нет отзывов