Siemens SENTRON 7KT PAC1600 Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 76

Siemens SENTRON 7KT PAC1600 Series Скачать руководство пользователя страница 27

Description

3.4 Parameterization

7KT multimeter
Manual, 08/2018, 2514284149-01

25

Note
The devices allow you to create a backup copy of the data which can be edited using the

keys in EEPROM. You can write this data back into RAM if required.
You can find more information on backing up and restoring this data in chapter Command

menu (Page 36).

3.4.2

Energy measurements

There are 3 special pages for energy meters:

●

Active energy

●

Reactive energy

●

Apparent energy

Each page shows the total value and the partial value. You can find information about

resetting in chapter Command menu (Page 36).

Continuous display of measurement

If the unit is displayed continuously, this means that the measuring device is set for imported

(positive) energy.
To activate the display for exported (negative) energies, set parameter P02.09 to ON.
These energies are highlighted by flashing of the unit and by a negative sign.

Imported active energy

«
...
25
26
27
28
29
...
»

Содержание SENTRON 7KT PAC1600 Series













































































Отзывы:

Нет отзывов