Siemens SENTRON 3WL Скачать руководство пользователя страница 20

Страница: 20 / 146

Description of blocks

3.1 Diagnostics block DIA_WLVL

Library SENTRON 3WL / 3VL for SIMATIC PCS 7

Function Manual, 11/2008, A5E02316914A-01

3.1.1

Calling OBs

The block must be installed in the processing sequence in the following OBs (occurs

automatically in the CFC):

OB1

Cyclic program

OB82  Diagnostic interrupt
OB83  Insert/remove module interrupt
OB85  Program error
OB86  Rack failure
OB100  Warm restart

Installation is performed automatically by means of the function "Generate Module Driver"

3.1.2

Called blocks

The block calls the following blocks:

SFC6

RD_SINFO

SFC51 RDSYSST

3.1.3

Function

The DIA_WLVL block is responsible for diagnosis of the 3WL / 3VL device.
If a 3WL / 3VL is directly connected to the DP master system, the block evaluates the acyclic

events that are relevant for 3WL / 3VL (start-up, DP station failure, module fault), generates

quality code and diagnostic information for the MOD_PAX0 block and provides the driver

block with status information via parameter output OMODE.
In the case of operation following a Y link DPV1, diagnostic information cannot be supplied

to the driver block. The block evaluates start-up, DP station failure and module faults and

provides the driver block with this information via parameter output OMODE.
This block is not used in the case of connection following Y link DPV0.

3.1.4

Message behavior

The block has no message behavior. The messages for DP station failure and module fault

are generated by the MOD_PAX0 block (in the case of direct connection to the DP master

system) or PADP_L00 (in the case of connection following the Y link DPV0) or OB_DIAG1 (in

the case of connection following the Y link DPV1).

Содержание SENTRON 3WL



















































































































































Результаты поиска

Содержание SENTRON 3WL

Отзывы:

Похожие инструкции для SENTRON 3WL

Бренды по названию

Популярные бренды

Siemens SENTRON 3WL, Руководство по эксплуатации функций

Результаты поиска

Содержание SENTRON 3WL

Отзывы:

Похожие инструкции для SENTRON 3WL

Бренды по названию

Популярные бренды