Siemens SENTRON 3WL Скачать руководство пользователя страница 101

Страница: 101 / 146

Description of blocks

3.3 Driver module DRV_3VL

Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01

Diagnostics and maintenance

In order to display the current state of the circuit breaker, modules present, statistics

information and diagnostic messages, the module reads the status word from the process

image and data records 91 and 92.
The process image is called in cycles. The user can request the data records in the faceplate

via operations. The diagnostic messages are updated in cycles when messages are present.

WARNING

During maintenance work on the circuit breaker, maintenance mode must be activated!
At the same time, the circuit breaker must be locked locally to prevent it being switched

back on.
Maintenance specifications apply to the circuit breakers (in accordance with EN 50 110-1,

DIN VDE 0105-100 and BGV A2).

Protect. parameter and extended protect. parameter

This data, which comes from data records 128 and 129, is updated for the display in the

faceplate if requested by the operator.
These parameters cannot be written.

Setpoints

These parameters can be read and written from the faceplate.

3.3.4

Message behavior

DRV_3VL issues the following messages:

Message block

Message

number

Message text

Message class

Overload tripping (L)

Instantaneous short-circuit (I)

Short-time-delay short-circuit (S)

Ground fault (G)

---

Overload in neutral conductor

Overload warning present

MSG_EVID1

An activated setpoint value has been exceeded

An alarm signal is currently present

Error time synchronization

Local turn off of circuit breaker / tripped

MSG_EVID2

---

Содержание SENTRON 3WL



















































































































































Результаты поиска

Содержание SENTRON 3WL

Отзывы:

Похожие инструкции для SENTRON 3WL

Бренды по названию

Популярные бренды

Siemens SENTRON 3WL, Руководство по эксплуатации функций

Результаты поиска

Содержание SENTRON 3WL

Отзывы:

Похожие инструкции для SENTRON 3WL

Бренды по названию

Популярные бренды