Siemens SENTRON 3WA Скачать руководство пользователя страница 76

Страница: 76 / 82

PROFINET IO

6.4 Interrupt, error and system messages

3WA Air Circuit Breaker Communication

System Manual, 11/2021, 92310000004-02

6.4.4

Process alarm messages

The process alarm messages are defined as follows specifically for the COM190:

UserStructIdentifier (hex) / message

UserData

0x0001

CubicleBUS² module status has

changed.

Current CubicleBUS² module status:

Length: 8 bytes

Refer to the description of the "ACTIVE_MODULES" data

point under Modbus register for the 3WA air circuit break-

(

https://support.industry.siemens.com/cs/ww/en/view/109

794278

0x0002

Status of the main contacts

of the circuit breaker has changed.

Length: 1 byte

0x01 = Main contacts open

0x02 = Main contacts closed

0x21 = Tripping via UVR

0x0003

Status of the ready-to-close signal has

changed.

Length: 1 byte

0x01 = Not ready to close

0x02 = Ready to close

0x0005

Status of the stored-energy spring has

changed.

Length: 1 byte

0x01 = Not charged

0x02 = Charged

0x0006

The protection parameter set of the cir-

cuit breaker has been changed.

0x01 = Protection parameter set A active

0x02 = Protection parameter set B active

0x0008

DAS+ status has changed.

Length: 1 byte

0x01 = DAS+ not active

0x02 = DAS+ active

0x0009

Status of remote operation protection has

changed.

Length: 1 byte

0x00 = All deactivated

0x01 = Remote parameterization protection activated

0x02 = Remote switching protection activated

0x03 = All activated

0x000A

Action is not possible when write protec-

tion is active.

Length: 1 byte

0x00 = Reserved

0x000B

Status of the threshold values has

changed.

Length: 1 byte

0x01 = No threshold value alarm active

0x02 = At least one threshold value alarm active

Содержание SENTRON 3WA



















































































Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды

Siemens SENTRON 3WA, Системное руководство

Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды