Siemens SENTRON 3WA Скачать руководство пользователя страница 24

Страница: 24 / 82

Status of the circuit breaker

3.7 DAS+ status

3WA Air Circuit Breaker Communication

System Manual, 11/2021, 92310000004-02

3.7

DAS+ status

The DAS+ maintenance mode basically comprises five registers:

•

DAS+ activation source (0x0FD2)

Indicates the source that was used to activate the DAS+ maintenance mode. It is

important to know the source, as the DAS+ maintenance mode can only be deactivated

again using the source that was used to activate it. For more information, see the section

"Activation source" below.

•

DAS+ status (0x0FD4)

Indicates whether maintenance mode is currently activated or deactivated.

•

Setting for current setting I

i DAS+

(0x1B5D)

The instantaneous short-circuit release is the most important protection parameter. For

more information, refer to Chapter "DAS+ maintenance mode" in the 3WA Equipment

Manual (Page 5).

•

Activation/deactivation of the DAS+ function (0xF619)

This command can be used to activate the DAS+ maintenance mode. If the DAS+

maintenance mode has been activated using this command, it must also be deactivated

using the same command.

•

Settings for ground-fault protection (0x2AFC to 0x2F26).

Depending on the implemented ground-fault protection, two protection parameters are

active: Current setting I

g DAS+

and tripping time t

g DAS+

DAS+ activation source

0x0FD2

DAS+ status

0x0FD4

INST DAS+ current setting I

i DAS+

0x1B5D

Activation/deactivation of the DAS+ function

0xF619

Settings for ground-fault protection
GFs HIZ UREF

Current setting I

g DAS+

0x2AFC

Tripping time t

g DAS+

0x2AFE

GFs DUAL UREF

Current setting I

g DAS+

0x2B10

Tripping time t

g DAS+

0x2B12

GFs DIRECT

Current setting I

g DAS+

0x2B24

Tripping time t

g DAS+

0x2B26

GFs RESIDUAL

Current setting I

g DAS+

0x2B30

Tripping time t

g DAS+

0x2B32

GFx HIZ UREF

Current setting I

g DAS+

0x2EE4

Tripping time t

g DAS+

0x2EE6

GFx DUAL UREF

Current setting I

g DAS+

0x2EFC

Tripping time t

g DAS+

0x2EFE

GFx DIRECT

Current setting I

g DAS+

0x2F14

Tripping time t

g DAS+

0x2F16

GFx RESIDUAL

Current setting I

g DAS+

0x2F24

Tripping time t

g DAS+

0x2F26

Содержание SENTRON 3WA



















































































Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды

Siemens SENTRON 3WA, Системное руководство

Результаты поиска

Содержание SENTRON 3WA

Отзывы:

Бренды по названию

Популярные бренды