manualshive.com logo in svg

Siemens SCALANCE XR524-8C, Руководство по эксплуатации, Страница: 29 / 100

Поделиться
Скачать
Siemens SCALANCE XR524-8C Скачать руководство пользователя страница 29

 

SCALANCE XR-500 
Operating Instructions, 05/2014, A5E03275845-05 

29

 

 

Assembling 

4 

4.1

 

Safety notices for installation 

Safety notices 

When installing the device, keep to the safety notices listed below. 

 

 

CAUTION 

Use only approved components 
If you use components and accessories that are not approved for SIMATIC NET devices or 

their target systems, this may violate the requirements and regulations for safety and 

electromagnetic compatibility. 

•

 

Use only components that are approved for SIMATIC NET devices. 

•

 

Create any supports you require according the dimension drawing. 

 

 

NOTICE 
Damage to the device due to inadequate cooling 
If the ventilation slits are fully or partly covered, the temperature inside the housing can rise 

and exceed the maximum permitted temperature causing damage to the device. 
The ventilation slits are located on the side panels of the housing. During installation, select 

a mounting position so that the ventilation slits are always free so that the air can circulate. 

The clearance to the ventilation slits of the housing must be at least 10 cm. 
You will find information about cleaning the air filter in the section "Upkeep and 

maintenance". 
Close unused module slots of modular devices with dummy covers. Open module slots 

impair the air circulation and can damage the device. 

 

 

NOTICE 
Warming and premature aging of the IE switch due to direct sunlight 
Direct sunlight can heat up the device and can lead to premature aging of the IE switch and 

its cabling. 
Provide suitable shade to protect the IE switch against direct sunlight. 

 

Содержание SCALANCE XR524-8C





































































































Отзывы:

Нет отзывов