Siemens SCALANCE XR-500 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 112

background image

Connecting

5.3 100 to 240 VAC power supply

SCALANCE XR-500

60

Operating Instructions, 05/2017, A5E03275845-11

5.3

100 to 240 VAC power supply

5.3.1

Power supply of the SCALANCE XR524-8C and SCALANCE XR526-8C

Notes on the power supply

WARNING

Danger from line voltage
The supply voltage for the devices listed is 100 to 240 VAC.
This device can only function correctly and safely if it is transported, stored, set up, and

installed correctly, and operated and maintained as recommended.
Connecting and disconnecting may only be performed by an electrical specialist.
Connect or disconnect power supply cables only when the power is turned off!

WARNING

Devices with a 100 to 240 VAC power supply do not have an ATEX or IECEx approval.
Devices with a 100 to 240 V AC power supply are not approved for use in hazardous areas

according to EC-RL-94/9 ATEX or IECEx.

NOTICE
Securing cables with dangerous voltage
Make sure that the connector cannot be released accidentally by pulling on the connecting

cable. Lay the cables in cable ducts or cable channels and secure the cables, where

necessary, with cable ties.

Note
Use in IT networks
When used in IT networks, the power supply 100 to 240 VAC also applies to the connected

IT network: Phase-to-phase.

Information on the power supply

The SCALANCE XR524-8C and SCALANCE XR526-8C are available in the following

versions for power supply with the 100 to 240 VAC power supply unit:

●

With single power supply unit (1 x 100 to 240 VAC)

●

With redundant power supply unit (2 x 100 to 240 VAC)
Each power supply unit PS1 and PS2 has its own 2-pin IEC plug C14 with switch.

To connect the power supply, use the cables listed in the section "Accessories (Page 20)".

«
...
58
59
60
61
62
...
»

Содержание SCALANCE XR-500

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XR-500

3C63100-AC-C - PathBuilder S600...

Бренд: 3Com Страницы: 232

ETHERLINE ACCESS U04TP01T

Бренд: LAPP Страницы: 16

Бренд: WoMaster Страницы: 2

Бренд: Gefen Страницы: 11

Бренд: Thinklogical Страницы: 27

Бренд: NTI Страницы: 15

Бренд: DX Engineering Страницы: 4

Бренд: Broadcast Pix Страницы: 478

Бренд: FIBERROAD Страницы: 30

Бренд: Aruba Networks Страницы: 40

CTRLink EISK8P-GT

Бренд: Contemporary Controls Страницы: 4

Бренд: IOGear Страницы: 10

Бренд: Lindy Страницы: 16

Бренд: Thinklogical Страницы: 45

Бренд: Abtus Страницы: 2

Digi-Touch DDN-SW1

Бренд: Blueridge Страницы: 13

Sun Network QDR InfiniBand Gateway Switch

Бренд: Oracle Страницы: 96

Бренд: I/O Interconnect Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды