Siemens SCALANCE XR-500 Скачать руководство пользователя страница 32

Страница: 32 / 112

Description of the device

3.4 C-PLUG / KEY-PLUG

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

Meaning in display mode C
In display mode C, the port LEDs indicate the mode.

LED color

LED status

Meaning

Off

Port operating in half duplex mode

Green

Port operating in full duplex mode

Meaning in display mode D
In display mode D, the port LEDs indicate whether the port is monitored.

LED color

LED status

Meaning

Off

Port is not monitored.

Green

Port is monitored for "Link down".
If no link was established at the port (e.g. cable not

plugged in), the signaling contact indicates an error.

Yellow

Port is monitored for "Link up".
If a link was established at the port, the signaling contact

indicates an error.

Meaning in display mode E
In display mode E, the port LEDs indicate whether the connected device is supplied using

PoE.

LED color

LED status

Meaning

Off

The connected device is not supplied using PoE.

Green

The connected device is supplied via PoE.

3.4

C-PLUG / KEY-PLUG

3.4.1

Function of the C-PLUG/KEY-PLUG

NOTICE
Do not remove or insert a C-PLUG/KEY-PLUG during operation
A C-PLUG/KEY-PLUG may only be removed or inserted when the device is turned off.

Содержание SCALANCE XR-500

















































































































Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-500, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды