Siemens SCALANCE XR-300WG Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 100

background image

6.8

Functional ground

Grounding options

Grounding (functional grounding) takes place via the mounting bracket on the device or via the
grounding screw at the front of the device.

Figure 6-7

Position of the grounding screw on the front of the device.

With 240 VAC variants the device is grounded via the power cable.

Functional ground

EMC disturbances are diverted to ground via the functional ground. This ensures the immunity
of the data transmission.

According to EN60204-1 (DIN/VDE 0113 T1) electrical circuits must be grounded. The chassis (0
V) is grounded at one defined point. Grounding is implemented with the lowest leakage
resistance to ground in the vicinity of the power feed-in.

With automation components, functional ground also ensures interference-free operation of a
controller. Via the functional ground, interference currents coupled in via the connecting cables
are discharged to ground.

Connect functional grounding via a grounding screw

The functional ground must be implemented with low impedance. The connection of the
functional ground must be established directly on the mounting plate or the DIN rail terminal.

To connect the functional ground, use a copper cable of category 20 AWG or a cable with a cross-
section ≥ 0.75 mm

2

.

①

Grounding terminal with cable

②

Grounding screw with spring washer and washer

Connecting up

6.8 Functional ground

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

65

«
...
63
64
65
66
67
...
»

Содержание SCALANCE XR-300WG





































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XR-300WG

Бренд: 3Com Страницы: 2

CoreBuilder 5000

Бренд: 3Com Страницы: 16

CoreBuilder 9000

Бренд: 3Com Страницы: 24

Бренд: H3C Страницы: 38

Бренд: H3C Страницы: 36

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 36

S12500X-AF Series

Бренд: H3C Страницы: 21

S12500X-AF Series

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 16

Бренд: H-Tronic Страницы: 32

Бренд: United Electric Controls Страницы: 6

Бренд: Cablematic Страницы: 8

Бренд: SMSC Страницы: 458

Бренд: Zamel Страницы: 2

Бренд: Niles Страницы: 7

Бренд: steute Страницы: 20

QuantaMesh T4000 Series

Бренд: QCT Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды