Siemens SCALANCE XR-300WG Скачать руководство пользователя страница 25

Страница: 25 / 100

Note

Active plug-in transceivers can be used with the following devices:
• SCALANCE XR328-4C WG

Pluggable transceiver SFP (1000 Mbps)

Type

Property

Article number

SFP992-1

1 x 1000 Mbps, LC port optical for glass FO cable
(multimode), up to max. 750 m

6GK5 992-1AL00-8AA0

10 packing unit (VPE 10)

6GK5 992-1AL00-8AC0

SFP992-1 (C)

1 x 1000 Mbps, LC port optical, for glass FO cable
(multimode), up to max. 750 m, varnished

6GK5 992-1AL00-8FA0

SFP992-1+

1 x 1000 Mbps, LC port optical for glass FO cable
(multimode), up to max. 2 km

6GK5 992-1AG00-8AA0

SFP992-1LD

1 x 1000 Mbps LC port optical for glass FO cable
(single mode) up to max. 10 km

6GK5 992-1AM00-8AA0

10 packing unit (VPE 10)

6GK5 992-1AM00-8AC0

SFP992-1LD (C)

1 x 1000 Mbps LC port optical for glass FO cable
(single mode) up to max. 10 km, varnished

6GK5 992-1AM00-8FA0

SFP992-1LD+

1 x 1000 Mbps LC port optical for glass FO cable
(single mode) up to max. 30 km

6GK5 992-1AM30-8AA0

SFP992-1LH

1 x 1000 Mbps LC port optical for glass FO cable
(single mode) up to max. 40 km

6GK5 992-1AN00-8AA0

SFP992-1LH+

1 x 1000 Mbps LC port optical for glass FO cable
(single mode) up to max. 70 km

6GK5 992-1AP00-8AA0

SFP992-1ELH

1 x 1000 Mbps LC port optical for glass FO cable
(single mode) up to max. 120 km

6GK5 992-1AQ00-8AA0

Pluggable transceivers with the supplement (C) in the type name have varnished printed circuit boards
(conformal coating).

Note
Restriction for pluggable transceivers

The maximum ambient temperature changes if you use pluggable transceivers:
• If you use pluggable transceivers of the types LH, LH+ or ELH, the maximum ambient

temperature is reduced to 50 °C.

For the values of the ambient temperature without pluggable transceivers, refer to the section
"Technical specifications (Page 71)".

Description of the device

4.3 Accessories

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Содержание SCALANCE XR-300WG





































































































Результаты поиска

Содержание SCALANCE XR-300WG

Отзывы:

Похожие инструкции для SCALANCE XR-300WG

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-300WG, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-300WG

Отзывы:

Похожие инструкции для SCALANCE XR-300WG

Бренды по названию

Популярные бренды